- ホーム
- > 洋書
- > 英文書
- > Science / Mathematics
Full Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 8th International Forum on Advanced Materials Science and Technology (IFAMST-8), was held in Fukuoka Institute of Technology, Fukuoka City, Japan, August 1-4, 2012. The forum attracted about 200 attendees from 10 different countries. The proceedings include 79 peer reviewed papers covering a wide range of up-to-date materials science topics.
Contents
Preface and Committees
Synthesis of MAX Phase (Cr,V)2AlC Thin Films
Study on Preparation Process of Magnetic Abrasive Particles
Fatigue Fracture of Clay Reinforced Nylon Nanocomposites
Crack Healing Behavior of SiC Whisker Reinforced Si3N4 Composite
Effect of Chemical Composition on Fracture Behavior in ZrNiAl Metal Glass
Effect of Minor Addition Ta on the Thermal Stability and Corrosion Resistance of Ti-Zr-Cu-Pd Bulk Metallic Glasses
Residual Stress in Oxide on NiCrAlY Coating Evaluated by Photoluminescence Spectroscope
Preparation of Ni-P-Al2O3 Composite Film on Mild Steel with High Resistance to Corrosion and Wear
Effects of Minor Si Addition on Glass Formation and Thermal Stability of Ni Free Ti-Based Bulk Metallic Glass
Influence of Carbon Reinforcements on the Mechanical Properties of Ti Composites via Powder Metallurgy and Hot Extrusion
Effect of Nanosized Particles on the Mechanical Properties of Y2O3
Three-Dimensional Characterization of BaZrO3 Precipitates in Y1-xGdxBa2Cu3O7-y Prepared by TFA-MOD Using STEM-Tomography
Ti-Based Bulk Metallic Glass Composites Produced by Spark Plasma Sintering
Fabrication of Cu Nanowires and its Effect on Proliferation of Mesenchymal Stem Cells
Electrochemical Behavior of AZ Magnesium Alloy Containing Rare Earth Element
Roll-Gap Control System of Twin Roll Strip Caster Based on Feed Forward-Feedback
Improvement of Catalytic Activity of Atomized Ni3Al Powder for Methanol Decomposition by Surface Chemical Treatments
Nanoporous Copper Dealloyed from a Nanocrystallized Ticu Alloy
Combined Experimental and Numerical Approach for Linking Microstructure and Mechanical Properties on Different Length Scales for near γ-TiAl Alloys
Development of ZnTe-Based Solar Cells
Peroxidase and Toluidine Blue-Incorporated DNA Bio-Polyion Complex Film as Biosensing Layer for Hydrogen Peroxide Determination
Dynamic Strain Ageing in a Twin-Induced Plasticity Steel
In Situ Synthesis of Alumina Matrix Composites by Spark Plasma Sintering
Temperature Field Analysis of Directional Solidification of Multi-Crystalline Silicon
Rheological Model for a Nanoporous-Elasto-Hydrodynamic Composite Material
Influence of Glass Coating Thickness on Interfacial Heat Transfer Coefficient during Forming of Nickel Based Superalloys
Shear Strength Evaluation of Laminated Binderless Bamboo Composites
Effect of Crack Initiation Size on Fatigue Strength in 0.85% Carbon Steel
Application of Magnetic Field Method for Measuring Lubricant Viscosity
Fabrication of Photo-Polymerized PCL Tissue Engineering Scaffolds by Dynamic Masking Rapid Prototyping System
FEM Analysis on Thermoelectric Properties of Metal/TiO2-x Composites with Random Distribution of Metal Powder
Improvement of Thermoelectric Properties of CuAlO2 by Excess Oxygen Doping in Annealing
Influence of Intermittent Air Introduction on Formation of Zn Films by Mechanical Coating Technique
Detection of Delamination in GFRP and CFRP by Microwaves with Focusing Mirror Sensor
Comparison of Mechanical Properties of a Biomedical β Titanium Alloy Added with Pure Rare Earth and Rare Earth Oxides
Mapping of Phase Distribution in Electron Holography with a Stage-Scanning System
Modeling and Simulation of Dynamic Recrystallization of GCr15 Steel Using Cellular Automaton Method
Investigation of Bonding Interface and Strength Properties in Diffusion Bonding of MgAZ31/Al6061
Analysis of Bonging Temperature and Interfacial Characterization of 3Y-TZP and SUS304 by Diffusion Bonding
The Effect of H3BO3 Microaddition on Microstructure of Ni/MgO Sintered Compact by Co-Precipitation Method
A Study on the Rust Removal and Retard on the Surface of the Wear Water Screw-Thread Steel Using Flame Hot Melting
Microstructure Evolution of AZ31 Magnesium Alloy in Rolling Zone
Study on the Application of Magnetic Nanoparticles as Drug Delivery Particles on the Atopic Dermatitis
A Pseudo-Binary Diagram of the (Bi,Pb)-Sr-Ca-Cu-O System
Synthesis of Spherical Carbon Nanoparticles via Sol-Gel and their Electrochemical Properties in Electrical Double Layer Capacitor
Effect of Mean Stress on Fatigue Strength of Spheroidal Graphite Cast Iron
Study on Anisotropic Mechanical Behavior at near Pre-Crack for AZ31B Sheet under Biaxial Stress
A Study on Spatial Resolution of the Microwave Atomic Force Microscope Imaging Affected by Scanning Speed
Thermal Residual Stress and Tensile Strength of UACS/Al Laminate with Different Slit Angles
Effects of Slit Patterns on the Tensile Properties of Unidirectionally Arrayed Chopped Strands Composites
Effect of Substrate on Crystallization of Sol-Gel-Derived Pb(Zr0.52Ti0.48)O3 Thin Films by Microwave Annealing
Structure Simulation Calculation of Impurities B with Fe, Al or Ca in Metallurgical Grade Silicon
Effect of Microwave Irradiation on Rapid Crystallization of Ferroelectric Lead Zirconate Titanate Thin Films
Preparation of Paver Bricks Having both Water Retainability and Frost Resistance by Designing Macro Porous Structure
Optimization of Process Parameters for Unidirectional Solidification of Magnesium Alloy
Notch Effects in High Cycle Fatigue of Ti-6Al-4V
Investigation for Small Shear-Mode Fatigue Cracks in Bearing Steels
Purification of Silicon Using the Liquid Phase Migration Technique under Temperature Gradient
Formation of Nanocrystalline Si by Au-Catalyzed CH3SiH3 Pulse Jet CVD
Photo-Electrochemical Properties of Titanium Dioxide Thin Films Prepared by Reactive RF Sputtering Method
Nanopore Formation on SOI(100) by CH3SiH3 Pulse Jet CVD: SiC Growth Temperature Dependence
Estimation for Fatigue Behavior of Notched Plate with Mean Stress Effect
Hydrogen-Induced Ductility Loss in Cast Irons
Effect of Occasional Shear Loading on Fatigue Crack Growth in 7075 Aluminum Alloy
Effect of Dry-Ice Blasting on the Microstructure and Properties of Plasma-Sprayed CoNiCrAlY Coating
Morphology and Residual Stress of Ultrathin Al Films Confined by AlN Layers
A High Sensitivity 3-D Measurement Method of Minute Specimen Based on Microscope and Laser Projection
Reductive Removal of Phosphorus in Silicon Using CaO-CaF2 Slag
Critical Current Characteristics and Flux Pinning in Fe-Based Pnictide Superconductor
Critical Current Density and Flux Pinning Properties in Superconducting MgB2 with and without SiC Doping
Structure and Electrochemical Properties of DLC/SiC Films on the Surface of Magnesium Alloy by Plasma Immersion Ion Deposition
The Effect of Working Pressure on the Composition and Optical Properties of TiO2 Films Bombarded by N Ion Beams
Glass-Forming Ability and Mechanical Properties of Zr-Ni-Al Bulk Metallic Glasses with High Zr Content
The Effect of Pt Addition on the Structure and Magnetic Properties of Melt-Spun Fe80-xPtxB20Alloys
Effect of Withdrawal Rate on Defects of Upgraded Metallurgical Grade (UMG)-Silicon Prepared by Vacuum Directional Solidification
The Research of Bubble Adsorption to Purify Silicon in the Al-Si System
A Developing Method to Prepare Micro-Nanopowder by Incorporating Jet Milling and Electrostatic Dispersion
Effects of Lanthanide Substitution on the Sintering Behavior of Bismuth Titanate Ceramics Prepared by the Chemical Coprecipitation Method
Development of Silicon Nitride Porous Bodies with Micro-Macro Complex Pore Structure for the Application of the 'Bio-Filter'
